Library Anti-Collision Strip
SKU: FL-LB-013
Stainless steel anti-collision strip for library shelves. 1m length.
| Material | SUS 304 stainless steel (1.0mm) |
|---|---|
| Manufacturing Process | Roll forming + bending |
| Surface Finish | Brushed stainless |
| Tolerance | ±0.5mm |
| Length | 1000mm |
| Width | 30mm |
| Height | 10mm |
| Mounting | Adhesive / screw |
| MOQ | 500 meters |
| Lead Time | Quoted after drawing review and process confirmation |
| Sample Time | Quoted after drawing review and process confirmation |
| Sample Fee | USD 80 |
| Price Range | USD 4-8/meter |
| Applications | Libraries, hospitals, schools |
| Compliance | REACH |
| Export Markets | USA, Germany, UK |
How This Library Anti-Collision Strip Is Fabricated and Checked
An anti-collision strip is a profile rather than a panel, so it is made by roll forming rather than press work. What matters is that the section stays consistent over the length and that the fixing method suits the surface it goes onto.
| Stage | What happens | What is verified before the job moves on |
|---|---|---|
| Coil and material check | Stainless coil checked for grade, thickness and surface condition before forming | The coil certification and the surface. A scratch in the coil runs for the whole length of the strip |
| Roll forming | The strip formed through rolls to the profile section | Leg lengths, the angle and the radius, measured on the first metres. A profile that is out of section will not sit flat along its length |
| Cut to length | Strip cut to length, with the cut ends treated | Cut length and end condition. An untreated cut end in stainless is a handling hazard |
| Straightness and twist check | Lengths checked for straightness and twist along the run | Straightness over the full length rather than at one point. A twisted strip will not sit on a flat shelf edge |
| Surface finish | Brushed finish applied to the specified grain, with the strip kept free of cross-grain marks | Grain direction consistency along the run, which is what the eye picks up on a long installation |
| Fixing provision | Adhesive backing applied, or screw holes made, to the design | That adhesive goes onto a clean dry surface, and that holes where used match the fixing pattern |
| Packing | Lengths bundled and protected against surface marking | That the brushed face is not marked in transit, and that the bundle can be handled without bending the profile |
What Can Change on Library Anti Collision Strip Library Metal Without New Tooling
Section and fixing method are the two variables on a profile; the material choice follows from where it is used.
| What can be changed | What it affects | What it does not affect |
|---|---|---|
| Profile section | The roll set, and how the strip sits against the surface | The material grade |
| Length | How it is bundled and handled, and how many joints the installation has | The profile |
| Material: stainless or coated steel | Appearance, corrosion behaviour and where it can be used | The process, which is roll forming either way |
| Fixing: adhesive, screw or both | The surface it goes onto and how permanent the installation is | The profile geometry |
| Finish and grain direction | How it reads along a long installation | Nothing structural |
| Packing and bundling | How the installer handles it on site | The strip itself |
Library Anti Collision Strip Library Metal Questions, Answered
Why roll form this rather than press brake it?
Because it is a long, constant profile. Roll forming gives a consistent section over metres, whereas braking a metre-long strip into the same shape gives a profile that varies along its length – and that variation is exactly what shows on a shelf edge.
Adhesive or screw fixing?
Adhesive is quicker and leaves the surface intact, and it works on a clean, flat, sound substrate. Screw fixing is more permanent and tolerates a rougher surface, but it puts holes into whatever it is fixed to. The surface decides which is honest.
Why does the grain direction matter?
Because a long brushed strip is read as one surface, and a change in grain direction halfway along is visible even when the sections themselves match. Lengths are kept in one direction through forming and finishing for that reason.
The section has to hold over metres, not over one sample length. Send the profile you need and the surface it goes onto through the RFQ form and the roll set and the fixing are matched to it. Related: custom sheet metal fabrication, surface finishing and material certification.
Adhesive or Screw: Choosing the Fixing Before the Profile
An anti-collision strip is a small part with an awkward job – it has to absorb a knock at the edge of a shelf or a counter without coming off, and it has to be replaceable when it is eventually damaged. Adhesive mounting is quick and leaves no holes, but it depends entirely on the substrate being clean, dry and sound, and it fails on a dusty or painted surface that was not prepared. Screw fixing is slower to install and needs countersinking, but it holds on almost anything and the strip can be replaced later. Choosing between them changes the profile: a screw-fixed strip needs a countersunk hole and enough material thickness to sink the head, an adhesive one needs a flat bonding face and a defined surface roughness.
- 304 stainless at 1.0 mm, roll formed, is the standard material – it takes the knock and it does not rust at a corner that gets bumped daily.
- Brushed finish runs along the strip; the grain direction on a mitred corner should match, or the joint reads as a defect.
- Lengths are 1000 mm as standard, which means a run longer than a metre needs a joint – and a joint is where a strip lifts first.
Roll Forming Versus Brake Pressing for Long Runs
Roll forming is the right process for a constant profile made in repeatable lengths: it is fast, consistent, and it holds a radius better than a fold. Brake pressing suits short runs, tapers and one-off lengths. Which one your order uses depends on quantity and on whether the length varies, and we tell you which route we are quoting rather than leaving it implied – because the two routes have different tooling costs and different minimum quantities.
Send the profile drawing with the fixing method, the lengths you need and the substrate the strip goes onto. If the installation is in a children’s area, say so: that is a case for screw fixing and for a radiused edge, and it changes the part. Lead time is quoted after drawing review and process confirmation.
Payment Terms
How a project is paid for is agreed before production starts, and the structure that applies to your order is stated on the quotation and on the order confirmation, so there is no ambiguity later.
- 30% advance payment with the order and the 70% balance before shipment — our standard structure.
- 70% advance payment with the order and the 30% balance before shipment — used for some projects.
- 100% payment in advance before production starts — used for some projects.
If your finance team works to a fixed structure, say so in the first enquiry and we will confirm what applies to your order before you commit. Request a quotation.
Questions buyers ask before sending drawings
The questions that come up most often before a project starts, answered the way we answer them by email.
What do you need from me to quote Library Anti-Collision Strip?
2D drawings as PDF, DWG or DXF, or 3D files as STEP, IGES or SolidWorks, together with material grade, sheet thickness, surface finish, quantity and destination country. If the drawing is not finished yet, send a photo, a sketch or the existing part instead — we review what can be measured from it and reply with the questions that still need answering.
How long does a quotation take?
Enquiries are answered within one business day. Simple laser-cut and bent parts are quoted within 24 hours. Welded frames, assembled units and multi-part structures are quoted after the drawing review and process confirmation, and the date is confirmed in our reply.
Is there a minimum order quantity?
Prototypes are made from a single piece and small batches of 10–50 pieces are routine. Prototype, first batch and repeat volume are quoted together so the numbers stay consistent as the project scales.
Can you work from a sample or a photo if I have no drawing?
Yes. Send the part itself, clear photographs with a rule or caliper in frame, or a dimensioned sketch. We measure what can be measured, list what is still undefined, and confirm it with you before production.
Need a Similar Part?
Most enquiries that start on a page like this are not an order for Library Anti-Collision Strip — they are a search for a factory that can make something like it. Send us your drawing, 3D model or sample and we will review the manufacturing process and the quotation requirements, then come back with a process plan, a price and a lead time.
We work from 2D drawings, STEP / DWG / DXF / PDF files, or a physical sample if that is all you have.
No complete drawings yet? Describe the part, send photos or a sketch, or send a sample — we can start from there. Discuss your project.
Trade Terms and Delivery
We quote under the standard Incoterms your logistics team already works with, and build the packing and documentation around the one you choose.
- EXW — you collect from our Ningbo facility and run export clearance through your own forwarder.
- FOB Ningbo — we deliver to the vessel at Ningbo port and handle export clearance.
- CIF — we cover carriage and insurance to your named destination port.
- DDP — we handle carriage, insurance, import clearance and duties through to your door.
Send your destination country, target delivery date and preferred trade term together with the drawing. Request a quotation.
Quotation Time
We quote from your drawings. How long that takes depends on what the part asks for:
- Simple parts — quoted within 24 hours. Laser-cut blanks and bent components, supplied with complete 2D or 3D drawings. Mon–Fri, GMT+8.
- Complex assemblies — quoted after the drawing review. Payment kiosks, multi-part welded frames, enclosures with purchased hardware, or anything needing a coating or assembly trial. We confirm a quotation date once the scope is clear.
Production lead time is quoted separately, after drawing review and process confirmation. Send your drawings.
What stands behind this quotation
- Manufacturing since 20162,500 m² Ningbo plant — 3 laser cutting machines (including newer TRUMPF), 4 CNC press brakes and 10 welding stations.
- Shipped to more than 30 export marketsEnclosures, cabinets and formed parts supplied to OEM buyers across Europe, North America and Asia.
- 123 documented product casesMedical device housings, HVAC and heat pump enclosures, agricultural and livestock equipment, industrial hydraulics, material handling trolleys and EV charging cabinets.
- Factory evidence you can checkTUV Rheinland audit reference MIC-ASI243729 and Bureau Veritas reference MIC-ASR263630 available for buyer review under NDA.
Before you send drawings: an NDA is signed on request · first-article inspection is carried out before a batch continues · pricing is staged from prototype quantity to repeat volume · pre-shipment photos and packing records are prepared when the project needs them.