Specifying Welded Frames: A Buyer’s RFQ Guide

Specifying Welded Frames: A Buyer’s RFQ Guide

An enquiry arrives for an “enclosure.” The attachment turns out to be three pages of a twenty-sheet welded skid-frame drawing set, the base frame has no flat pattern, and the steel grade on the cover belongs to a regional standard the buyer assumes is interchangeable. A quote built on that brief will be wrong on process, price and schedule. This guide gives equipment buyers a working framework for defining a welded sheet-metal structure before the RFQ goes out, so the numbers you receive are comparable and the first article passes on the first attempt.

What Makes a Welded Frame Different from a Folded Enclosure

A welded frame (often called a skid frame, bed frame or structural weldment) is an assembly of sheet, plate or tube components joined into a load-bearing or machine-mounting structure. A folded enclosure is primarily bent panels closed with fasteners and seams. The distinction matters commercially: a weldment carries labour for joint preparation and welding, cost for fixtures and tack jigs, and time for distortion control and post-weld dressing. Two parts of similar weight can therefore sit far apart in price.

When the drawing title says one thing and the email says another, pause before quoting. Ask the buyer to confirm whether the requirement is a folded housing or a welded structural base, because the process route, inspection plan and tooling are different for each. In our shop a welded program draws on ten welding stations, four production lines, three lasers (two 3000 W and one 6000 W) and four 250 t CNC press brakes with 3000 mm beds. Forming and cutting are in-house; when a finish such as anodizing, passivation, plating or powder coating is required, it is handled by vetted subcontractors.

Material envelopes are worth stating early in any technical conversation: carbon steel 0.5–18 mm, stainless steel 0.5–15 mm and aluminum 0.5–10 mm, with common grades including SUS304, SUS316, SUS430 and aluminum 5052, 5754 and 6061. These are working ranges, not a promise that every grade and thickness combination is suitable for every welding process. [需确认: exact process and consumable list per material/thickness combination, to be confirmed by the workshop before publication]

Five Inputs That Decide a Welded-Frame Quote

1. A complete drawing set. A three-page sample out of twenty sheets cannot support a firm price. The parts that usually move the number most are precisely the ones left out of samples: the bed frame and the support members, where flat patterns and developed dimensions are not visible. Request the full set in PDF or DXF/DWG before committing to a figure, and treat any earlier number as an indication only.

2. Material and written equivalence. Buyers often specify a grade from their local standard and ask whether a Chinese equivalent is acceptable. Substitution should be confirmed in writing rather than assumed, especially where the assembly serves marine, pressure or safety-related equipment. Ask at the RFQ stage whether mill certificates or classification-society documentation (for example LR, DNV or KR) will be required, since that changes both sourcing and inspection. [需确认: whether mill certificates are issued per heat or per batch, and which classification-society documents can be supported]

3. A usable weld definition. “Weld as shown” is rarely enough. Define the joint type, fillet leg size, continuous versus intermittent stitching, cosmetic grinding requirements, and whether a leak, load or flatness test applies. Where a drawing is silent, ask the buyer to confirm the acceptance basis instead of pricing a best guess.

4. Stated process assumptions. A cooler or ventilation cover with roughly 1,200 to 1,400 small square holes is a CNC-punching job. Quoting it as laser cutting inflates both lead time and cost, and leaves the fabricator exposed when the assumed route changes. Put the assumed process in the quotation so both sides can challenge it before an order is placed.

5. Quantity and annual volume. Trial quantity and estimated yearly volume drive fixture amortisation, programming effort and unit price. A welded frame quoted at five pieces and the same frame quoted at five hundred are different manufacturing problems, not a simple discount ladder.

How Tolerances and Inspection Are Agreed

Before production, agree which surfaces are functional and which are cosmetic, and fix a datum scheme the drawing actually references. Flatness on a welded frame is decided as much by weld sequence and fixturing as by the press brake: a part that measured true before welding can bow once heat is applied. Control it with tack fixtures, balanced weld sequence and in-process checks rather than trying to correct it at the end.

In-house verification uses digital calipers, micrometers, digital height gauges, a granite surface plate, radius, thread, pin, weld and plug gauges, a surface roughness tester, and custom go/no-go fixtures built for the part. When a buyer requires full three-dimensional dimensional verification beyond these methods, that work goes to an outside metrology lab [需确认: whether the external lab’s name may be disclosed; currently described as a named third-party metrology lab, name available on request]. We do not operate a coordinate measuring machine in our own shop, and the quotation should say so plainly rather than imply otherwise.

Our quality system is documented to ISO 9001. Independent audit references include TÜV MIC-ASI243729 and BV MIC-ASR263630, verifiable under NDA. A signed inspection report accompanies every shipment. These documents support a buyer’s supplier review; they are not a substitute for agreeing the specific acceptance criteria on your drawing.

FAQ: Welded-Frame RFQs

Can you quote a welded frame from a partial drawing set?

Only as an indication. A few sample sheets are useful for checking scope and rough complexity, but members without flat patterns or developed dimensions cannot be priced reliably. Send the full set and you will get an itemised quotation you can actually budget against.

Can you use an equivalent steel grade instead of the one on our drawing?

Often yes, but equivalence should be confirmed in writing part by part. Tell us the governing standard and whether the assembly has marine, pressure or other regulated duties, and we will confirm what can be substituted and what documentation is needed.

What should I specify for welds on a sheet-metal drawing?

At minimum: joint type, fillet leg size, continuous or intermittent pattern, any grinding or cosmetic requirement, and the test that defines acceptance. If your drawing uses a welding symbol standard, reference it explicitly so there is no ambiguity about interpretation.

How is flatness on a welded frame controlled and measured?

Through fixturing, weld sequence and in-process checks, then verified against the agreed datum on a granite surface plate with height gauges and part-specific fixtures. If your requirement needs full 3D dimensional reporting, we arrange an outside metrology lab and state that scope in the quote.

What are the typical lead times for a welded assembly?

Simple samples run 3–7 days; a complex first article takes 15–20 days; production lots run 25–35 days. Welded structures with fixtures or special inspection can sit at the longer end, so confirm the schedule alongside the technical scope.

Do you support certification and inspection documentation?

We can provide the audit references above, a signed inspection report with each shipment, and material traceability where it has been agreed in the RFQ. Tell us which documents your quality team requires at enquiry stage so they are built into the quote.

Buyer’s Pre-RFQ Checklist

  • Full drawing set (PDF plus DXF/DWG), including flat patterns for formed members
  • Confirmed scope: folded enclosure or welded structural frame, with any naming mismatch resolved
  • Material grade and written approval of any equivalent, plus required certificates
  • Weld definition: joint, leg size, stitch pattern, cosmetic standard and acceptance test
  • Datum scheme and which tolerances are functional rather than cosmetic
  • Stated process assumptions for perforations and other high-feature-count operations
  • Trial quantity, estimated annual volume, finish specification and delivery term

The same discipline applies to welded trolley and cart frames. For buyers who need a ready-made cart or trolley series rather than a custom fabrication program, see our dedicated site doingmetal.com.

Planning a welded frame or skid structure? Send the drawing set and the checklist above to our engineering team via our contact page. We will return the questions, process assumptions and an itemised quotation before you commit. We support buyers across Industrial Automation · EV Charging · Medical · HVAC · Semiconductor · Robotics · Renewable Energy.

What stands behind this quotation

  • Manufacturing since 20162,500 m² Ningbo plant — 3 laser cutting machines (including newer TRUMPF), 4 CNC press brakes and 10 welding stations.
  • Shipped to more than 30 export marketsEnclosures, cabinets and formed parts supplied to OEM buyers across Europe, North America and Asia.
  • 123 documented product casesMedical device housings, HVAC and heat pump enclosures, agricultural and livestock equipment, industrial hydraulics, material handling trolleys and EV charging cabinets.
  • Factory evidence you can checkTUV Rheinland audit reference MIC-ASI243729 and Bureau Veritas reference MIC-ASR263630 available for buyer review on request.

Before you send drawings: project confidentiality is default · first-article inspection is carried out before a batch continues · pricing is staged from prototype quantity to repeat volume · pre-shipment photos and packing records are prepared when the project needs them.

Scroll to Top